Category Archives: Allgemein

Reset function on the CPplus

Posted on by

The spanner in the lower right-hand area of the display is used to access the settings menu of the CPplus operating element. And it is here that you will find the menu item “Reset”. However, many people are unfamiliar with its function.

When the CPplus is delivered, it is completely blank with regard to the units to be controlled. The device memory is empty. During the vehicle conversion at the caravan or motor home manufacturer, the vehicle technology is implemented step by step into the body and at some point the gas supply and heating and air conditioning system from our company is also installed. In order to be able to operate and monitor all Truma devices, the device memory in the CPplus must finally be filled. And this is what the reset function is for. By pressing the control knob when “RESET” is shown on the display, I activate this function and “PRSET” appears. Press the control knob again to delete the unit’s memory. After this, “INIT” appears; all units connected to the CPplus with a TIN cable and supplied with voltage at the time of initialisation are now written into the unit memory of the CPplus. Only at this point can they be controlled with the operating element. All symbols belonging to the units are then stored on the display and can be selected.

Please note that a reset is never used to reset an error code. If, for example, the heater reports a gas error ( E506H, E516H or E517H), the reset automatically locks the control electronics of the heater for 15 minutes. If a reset is activated with the warning message W255H, which indicates that the control element has lost contact with the heater, then the CPplus is returned to the delivery state without a connected heater. In this case, the power supply of the heater and the TIN connection cable to the heater should be checked first.

Caution with accessories from the 3D printer

Posted on by

In view of this, we would like to point out that many online portals and trading platforms offer accessory products and 3D files for the manufacture of components that are supposed to improve the function of our Truma devices or remedy side effects. These products may appear to be useful and may be of good quality, but in most cases they have not been tested, authorised or approved by us.

An example of this is the product known as the drip lip / drip guide or condensation drain for mounting on the flue of the Combi heater. It does not come from our company and its installation even invalidates the operating permit and warranty as an unauthorised modification to the appliance.

As described in our operating instructions and the installation instructions, no safety-relevant component may be changed. However, the side wall chimney and its individual components belong to this area. After such a change, the appliance may no longer be put into operation from a legal point of view. Interactions with the accessory product are unknown.

This circumstance can perhaps be compared to the installation of a sports exhaust system for a passenger car: if there is no expert opinion or ABE for the system, in which the vehicle model is not explicitly mentioned, then it is also not permitted to install it. Use on public roads is prohibited. If you are caught, you are also liable to prosecution for “driving without an operating licence”. The consequence is a trip to the TÜV and a fine.

In the case of the above-mentioned accessories, there is no mention of whether the material used can withstand the temperatures applied to the side wall chimney, nor is there any guarantee that the imperative openings for combustion air intake and exhaust gas disposal will be affected in any way. In such cases, for example, due to an incorrectly supplied amount of oxygen or reduced cross-section of the flue gas opening, the burner of your heating system may not work correctly and error messages may occur during heating operation.

In the worst case, damage to the vehicle may occur if, for example, the material of the accessory was not designed for the temperatures on the side wall chimney.

So if in doubt, please contact the Truma Service Centre, our authorised dealers or service partners. Here you can clarify whether such an accessory comes from our production and whether there are justified objections regarding its function or the effect on an existing approval.

W255H in digital control panel or no device detection after reset

Posted on by

You see the warning message “W255H” on your digital display and cannot control your heating anymore?
This primarily indicates a connection problem between the digital control panel and the heating. In this state, commands entered cannot be transmitted or cannot be transmitted correctly.

Attention!
A reset on the CP plus is not used to delete an error, but corresponds to an initialisation, i.e. a device search.
If the reset is carried out while there is a connection problem to the heating, the heating menu is completely lost. Only the time and the setup symbol remain.

Two factors can be considered as causes of the connection problem:

  1. 12 V power supply

Communication is only possible if the heater is powered in addition to the control unit. If this is not the case, the control panel responds with the message W255H.
Please check the heating fuse in your electrical block as well as the fuse on the control board of the heating (Combi) or in the supply line (Varioheat). Replace a defective fuse if necessary.

Note: In our installation instructions, we recommend installing our units on permanent plus.
This means that the power supply to our units cannot be switched off by the central control element (main panel). There should be a permanent connection via the electrical block to the body battery.

  1. TIN connection cable

The TIN cable is used to transmit commands from the control panel to the heater. If this connection is interrupted, the control panel responds with the message W255H.
Please check whether the plug of the TIN cable is correctly seated in the socket on both the control element and the control board of the heater.


As soon as the cause is eliminated, the warning message disappears automatically from the display.

Advice for Combi D: If the installed TIN cables exceed a total length of 12 metres, an error may occur in the communication with the digital control unit (W255H). The “control panel cable coupling” accessory provides a remedy.

Please place this coupling between the TIN socket on the heater and the TIN cable. If two TIN sockets are occupied, it does not matter which of the two TIN cables the coupling is used with.

The article “control panel cable coupling” can be ordered from our specialist dealer (part number 39050-00175).

New update for the Truma App (4.9.3) and Truma iNet Box (2.09.00)

Posted on by
  • We have added a few new features to the Truma LevelControl functions in the app. You can now easily initiate a new measurement. The result is also now shown together with the time of the measurement.
  • Alde heater owners can now activate / deactivate automatic climate control via SMS if they have a Truma air conditioning system installed.
  • We also have good news for all Combi D users:
    The “255H” and “164 H” bugs (continuous sending of SMS) have been fixed with this update and the heater can once again be used without restrictions.

Good2know:

This is how you can see what the status of the system is or whether an update is pending.

  1. open the Truma App – Settings – “iNet Box Update”
  2. at the bottom you will see the version information
  3. after the current update, these are:

Truma App version = current state of your app
iNet Box FW = Firmware version of your iNetBox
Server = available firmware version (update) on the Truma server
Local = firmware version, you have downloaded

If you have any questions or feedback, please use the comment function.
We look forward to exchanging ideas with you.

Truma iNetBox – What you ever wanted to know

Posted on by

Hello campers, do you have questions about Truma iNetBox? Just use the comment function. We will be happy to answer them.

The Power LED is permanently turned “green”. The GSM LED flashes “red”. Is that ok?

A: Everything is fine! -> As long as you have not yet completed the GSM setup, the red LED will continue to flash. If you have completed the setup, it will go out.

The box is permanently supplied with 12V, even if the main switch is set to “Off”. How can the box be switched off?

A: It is not intended to switch off the box, otherwise you will not be able to use the remote control. In case of a main switch you can connect the box to the corresponding circuit.

Do I need the box, even if I don’t have an app installed?

A: Box and APP are inseparably connected. Without an app you cannot use a box. You can also use the app on its own, the range of functions is accordingly smaller.

There is a new update for Box and App available? How do I find out which one I have and what is up to date?

A: Start the Truma App and go to “Settings\Truma iNet Box Update”, there you will find all information below the “START UPDATE” button.

Truma App version = Describes the current state of your app
iNet Box FW = Software version of your iNetBox firmware
Server = The available firmware version (update) on the Truma server
Local = Describes which firmware version you have downloaded

iOS13 connection problems

Posted on by

Since the iOS13 release, connection problems between iPhone/iPad and the Truma iNet Box occur. In the meantime, we have been able to identify two different issues – but have not yet been able to solve the problems, even in cooperation with Apple support.

Here you can find a detailed error description and technical information about the causes of the problems. As soon as we have new findings, we will keep you up to date in the Truma service blog and in the App News.

Have you had experiences that you would like to share with other users and us? Then use the comment function in our service blog! We look forward to exchanging ideas with you.

Continue reading →

Important information about the new Truma App release in March 2018

Posted on by

Integrate your Alde heater into the iNet System

Good news for Alde heater users. From April 2018, you will be able to integrate the Alde compact 3020 HE with new control panel into the Truma iNet System. All you have to do is connect the heater to the iNet Box.

  • This is great news above all for campers who use or would like to use a Truma air conditioning system or Truma LevelControl. You can now conveniently use all devices via the iNet System. From controlling the heater and air conditioning to using the automatic climate control and checking the gas level, all it takes is a single app.
  • The new version of the Truma App will be available from March 2018.

Important: Deactivate the automatic update function

  • Previously, Truma App users could download new releases to their smart phone and still have two months to install the new firmware onto the iNet Box via Bluetooth.
  • For the new update, the complexity of the project forced us to suspend this rule. This means that the two-month time frame does not apply for this release. You must update both your app and the iNet Box with the new firmware simultaneously.
  • If you have automatic updates activated in the Truma App, please deactivate this function and switch to manual updates. This will allow you to decide when you wish to install the update.
  • Otherwise, the app will perform the update automatically. If there is no Bluetooth connection to your iNet Box at this time, it will not be possible to update the firmware. The iNet Box will then no longer function until the new firmware is installed.
  • This is particularly important for campers who have parked their vehicle outside Bluetooth range and wish to use the iNet System.
  • For the next releases, the two-month time frame will apply as usual.

Do you have any questions? The Truma Service team will be happy to help.

Movers for caravans: what is important

Posted on by

You finally arrive at your holiday destination after a long journey. Now all you want to do is get the caravan set up and relax. If you want to position your caravan manually, you will need patience and high levels of physical strength. However, if you have a mover, you can simply manoeuvre your caravan safely into the correct position by remote control.

Truma_Mover_XT_rangieren_1000x750

The benefits of a manoeuvring tool

Continue reading →

No more empty gas cylinders

Posted on by

Gas cylinders have the annoying habit of becoming empty in the middle of the night. You can put a stop to this with the Truma DuoControl CS which automatically switches from the empty operating cylinder to the reserve.

Truma_DuoControl_CS_vertikal_1000x750

The Truma dual-cylinder gas pressure regulator automatically switches to the reserve cylinder. The integrated crash sensor allows you to operate the gas system safely even when on the road.

Continue reading →

Make optimum use of your air conditioning system in the caravan

Posted on by

With an air conditioning system from Truma you can always have exactly the temperature you want inside your vehicle. It is not only the cooling output that counts, there is another function of the air conditioning system that is equally as important: it can dehumidify the air reliably. The higher the room temperature, the lower the humidity should be, because the body can discharge excess heat much more easily when the room air is dry. A high level of humidity often feels oppressive.  The temperature and humidity level are perfectly aligned in all air conditioning systems from Truma.

Truma_Klimaanlage_optimal_nutzen_1000x750Even if the weather is tropical outside, you should only cool down your motorhome or caravanmoderately. Experts recommend only cooling the temperature by around six degrees. This even applies when it is 35°C in the shade. If the temperature difference between the inside and the outside is too large, then this can lead to circulatory problems and illness.

Here are more tips:

Continue reading →